CD3000 Series | CD3000S | CD3000M | CD3200 Thyristor Unit

Famous CD3000 Series | CD3000S | CD3000M | CD3200 Thyristor Unit

DM_series_CD_3000-1PHDM_series_CD_3000-2PHDM_series_CD_3000-3PHDM_series_CD_Multidrive

CD3000 Series

  • Suitable for loads up to 700A (1-2PH) and 500A (3PH)
  • Heater Break (HB) alarm to diagnostic partial or total load failure and short circuit on Thyristors as option
  • IP20 protection
  • cUL us available as an Option

CD3000S 1-2-3PH

  • Resistive load,
  • ZC Firing and SSR Input

CD3000M 1-2-3PH

  • Resistive load and IR Lamp
  • ZC Firing and SSR Input
  • BF Firing and Analogue Input
  • SC & PA Firing and Analogue Input on 1PH

CD3200

  • Inductive load,
  • PA Firing and Analogue Input
  • Soft Start and Current Limit

ShareEmail this to someonePrint this page
DM_series_CD_3000-1PHDM_series_CD_3000-2PHDM_series_CD_3000-3PHDM_series_CD_Multidrive

CD3000S 1-2-3PH

  • Suitable for resistive loads up to 700A (1-2PH) and 500A (3PH)
  • Zero crossing firing mode (ZC)
  • Logic input signal 4 to 30Vdc (SSR)
  • Constant current drain with SSR input
  • Heater Break (HB) alarm to diagnostic partial or total load failure and short circuit on Thyristors as option
  • Side by side packaging
  • Special design Heatsink with high dissipation
  • IP20 protection

Option available only for specific part of the range:

  • Burst Firing (4, 8 or 16 cycles selectable, 25A to 110A on 1PH and 35 to 100A on 2PH)
  • ACDC linear 4-20mA loop powered, 4-20mA or 0-10V input
  • AC input 110V AC or 230V
  • cUl us on basic model.

 Manuals and Datasheet

  1. 1
    CD3000S-1PH
  2. 2
    CD3000S-2PH
  3. 3
    CD3000S-3PH


ShareEmail this to someonePrint this page

DM_series_CD_3200DM_series_CD_3000-MDM_series_CD_Multidrive

CD3000M 1PH

  • Single phase Thyristor unit up to 700A
  • Suitable to drive resistive loads with zero cross firing (ZC) modes and inductive loads with phase angle (PA) mode
  • Universal input signal (SSR, 0-10V, 4-20mA, 10K Pot)
  • Universal firing, customer configurable via serial port for zero crossing (ZC), single cycle (SC), burst firing (BF), delayed triggering (DT) and phase angle (PA)
  • Soft Start can be used with single cycle, burst firing and phase angle
  • RS485 comms, MODBUS protocol included as standard
  • Heater Break circuit microprocessor based to diagnose load failure and short circuit on Thyristors as option
  • IP20 Protection

CD3000M 2PH

  • Two leg switching of three wire star or delta resistive loads
  • Suitable for loads up to 700A
  • Microprocessor based electonic circuit fully isolated from power
  • Universal input signal with automatic zero/span calibration
  • Universal firing, customer configurable via serial port for zero crossing (ZC) and burst firing (BF) modes
  • RS485 comms, MODBUS protocol included as standard
  • Heater Break circuit microprocessor based to diagnose load failure and short circuit on Thyristors as option
  • IP20 Protection

CD3000M 3PH

  • Three leg switching of 3/4 wire star or 3/6 wire delta resistive loads
  • Suitable for loads up to 500A
  • Microprocessor based electronic circuit fully isolated from power
  • Universal input signal with automatic zero/span calibration
  • Universal firing, customer configurable via serial port for zero crossing (ZC), and burst firing (BF) modes
  • RS485 comms, MODBUS protocol included as standard
  • Heater Break circuit microprocessor based to diagnose load failure and short circuit on Thyristors as option
  • IP20 Protection

Manuals and Datasheet

  1. 1
    CD3000M-1PH
  2. 2
    CD3000M-2PH
  3. 3
    CD3000M-3PH
  4. 4
    Software


    Thyristor Configurator V5.3.0.7- CD3000 series – MULTUDRIVE (17.1 MB, 298 downloads)



ShareEmail this to someonePrint this page

DM_series_CD_3000-MDM_series_CD_3200

 

CD3200

  • Phase angle firing (PA) with soft start
  • Microprocessor based electronic circuit fully isolated from power
  • Universal input signal
  • Selectable feedback mode: V, I, V2 and VxI
  • Adjustable current limit
  • Profiling of current limit by analogue input
  • Configurable digital input
  • RS485 Comms MODBUS protocol as standard
  • Heater Break circuit microprocessor based to diagnose load failure and short circuit on Thyristor as option
  • Monitoring & control via external keypad (CD-KP)IP20 Protection

Manuals and Datasheet

  1. 1
    CD3200
  2. 2
    Software


    Thyristor Configurator V5.3.0.7- CD3000 series – MULTUDRIVE (17.1 MB, 298 downloads)



ShareEmail this to someonePrint this page